sintering造句
91. It is mainly used for sintering of hard alloy, magnetic alloy, ceramic and powder materials.
92. By selection of discharging parameters, low-voltage electromagnetic EMC increases the compacted density and improves sintering character of PZT ceramics, compared with static die compaction.
93. The effects of diamond grain sizes on wear resistance ratio of the sintering diamond compacts are investigated.
94. The crystal size is about 20nm from XRD results. The PZT5 nano-ceramic was prepared by traditional processing and two-step sintering with PZT5 nano-powders prepared by high-energy ball milling.
95. A novel route-reactive crystallization technology, directly mixing fluormica crystals with soda-lime glass powder and sintering, was proposed to fabricate machinable fluoramphibole glass-ceramics.
96. CrMnN steel casting is the key for sintering machine to produce sintering mine in metallurgy enterprises.
97. The change of base metals in the raw material preparation, sintering and their behaviour in blast furnace smelting has been discussed and a brief balance is also given.
98. The characteristics and process of the coated sand mold (core)made by selective laser sintering rapid prototyping are introduced.
99. The effect of the technological conditions such as molding method, raw material proportioning, pugging times and sintering system on the performances of porous permeable bricks was studied.
100. A machinable fluoramphibole glass-ceramic was fabricated by directly mixing fluormica crystals with recycled glass powder and sintering.
101. The dynamic sprinkler developed by Masteel tech-center can satisfy the requirement of homogeneous insufflation sintering.
102. The effect of sintering process and glass content on the coating properties was researched. A heat-resistant silicone resin is selected as a good coating of organic material by TGA and IR test.
103. We have succeeded in making a kind of phase change material (PCM) of high thermal storage density, good corrosion-resistant performance and low cost of preparation by powder sintering method.
104. Unwrought tantalum, including bars and rods obtained simply by sintering; powders.
105. Based on the synthesis of Q phase by the predecessors, the paper studied the sintering conditions of various minerals of Q phase- CA- C12A7 system cement by the orthodoxy experiment.
106. The influence of process parameter to laser sintering process is discussed.
107. In experimental study, Ti powder was chosen for spraying onto eroded diamond segments made by hot-pressing sintering, fracture on which was made for microscope investigation.
108. Sintering Machine Design paperless design will greatly reduce the workload of workers.
109. The results suggest that the KOH can lower down the synthesized temperature by 300 K, and the as-synthesized powder smaller and easier to densify in the sintering process.
110. For a selection of samples, the final grain size after sintering was measured using a Quantimet image analyser.
111. The electrostriction in the Lanthanum-doped Lead Zirconate-Titanate(PLZT)ceramics with hot pressed and non-hot pressed sintering is investigated.
112. Through using the theory analysis and calculated method, writers analysis it will cause effect on sintering process if the refined iron powder is used.
113. Machinability of P/M sintered steels with manganese sulfide and calcium fluoride additives is investigated and analyzed by experiments of sintering and cutting on milling machine.
114. Ternary boride based cermet cladding material was prepared by in situ reaction and liquid phase sintering technology in vacuum furnace.
115. And the result of the experiments shows that the components and sintering temperament are the key factors of preparing forsterite ceramic.
116. It produces rebonded magnizium-zirconium bricks which is made up of fused magnesite and fused eutectic MgO-Z_rO_2 materials. Then it analyzed the properties of samples after sintering.
117. It was concluded that the three key technologies are the glass microsphere classifying, MSP body molding and sintering, dynode making of MSP.
118. The influence of sintering temperature and holding time on the density, micro-structure and mechanical properties of the ceramic tool materials are studied.
119. In sintering process, for melted mineral fines bind unmelted core ores when cooled, the self-intensity of binding phase in iron ores is one of the basic indexes to estimate sintered binding status.
120. Modified polyacrylic acid aqueous vehicle may be most applied in electronic pastes of high sintering temperature.
1234567