quenched造句
31. So long Spencer, it was short but hopefully it quenched your Survivor thirst.
32. The quenching mechanism was studied in a quenched dye laser pumped by excimer lasers.
33. Col workingdie steel with high abrasion resistance for general use , Super hardenability and minimal quenched stress.
34. The results show that the fluorescence of BSA was quenched regularly by the pentachlorophenol, the mechanism of the fluorescence quench was investigated.
35. The mechanism of cutting force, cutting temperature and tool wear in the machining of quenched steel and nickel based high temperature alloy with ceramic tools are analyzed in the paper.
36. When such a quenched steel is tempered, structures with mechanical properties intermediate between those of the slowly cooled and the quenched conditions are formed.
37. His unjust unkindness, that in all reason should have quenched her love.
38. The effect of interrupted quenching temperature on the microstructure and mechanical properties of a direct quenched and self tempered martensitic steel has been investigated.
39. Based on the results of laboratory experiment, the technical parameters of laser quenching process were selected. The roughing roll of Wire Rod Mill at Pangang was laser quenched.
40. The superplasticity research was carried out under constant temperature compression deformation for salt-bath cyclic quenched and high frequency hardened T10A steel.
41. The fluorescence of AaH - 1 is quenched by I ~ -, acrylamide and N - bromosuccini - mide ( NBS ).
42. Machine rectangular table guide face and super - audio have been quenched, perishable wear - resistant .
43. The phase transition process of isothermally quenched ductile iron was investigated, the author's opi.
44. The paper studies the chemical composition of steel for racing bicycle chain and the mechanical properties after being quenched, then the optimum chemical composition of steel is determined.
45. The results show that, in cutting teat, best cutting speed exists for different quenched steel.
46. The evaluation of measuring uncertainty in metallic material Brinell hardness test is studied by testing the hardness of the 45 quenched and tempered steel.
47. The steel should then be reheated to a point above the transformation range of the case and quenched to produce a hard, fine structure.
48. Compared with the as-cast composite and hadfield steel, the water quenched composite possesses great wear-resistant behavior.
49. The utilization of water quenched slag ferromanganese blast furnace is discussed.
50. The grinding force ratio in grind-hardening consists with the grinding force ratio in grinding quenched steel, and is bigger than the grinding force ratio in grinding unquenched steel.
51. The test has been demonstrated that the boron segregation at austenite grain boundaries in quenched steel is a non-equilibrium grain boundary segregation phenomena occurred during cooling.
52. Micron scale spheres may be preserved in quenched volcanic matrix.
53. Study shows that quenched boron eutectic structure possesses the excellent wear abrasion property.
54. The effect of chemical composition on mechanical properties of the austenite - bainite ( is other - tally quenched ) white iron was investigated.
55. The effect of V on nodulizing of carbides was observed in the as-cast, nomalized and oil quenched condition in low Cr white cast iron alloyed with V.
56. The surface of inoculated cast iron HT300 chain wheel is quenched by laser for improving its antiwear property and increasing its surface hardness, therefore prolonging its life.
57. High carbon steel will be gain a more amount of undissolved(remained) carbide and higher hardness when the steel is quenched with austenite of non homogeneous chemical composition.
58. The cutting experiments show that in cutting of quenched steel the tool life of this cutter is longer than that of uncoated cutting tool.
59. The critical properties of a quenched site - correlated percolation system is treated by real - space renormalization group method.
60. The nucleation and growth of dislocation loops and voids in quenched face-centred cubic metals have been studied.
123