CMOS造句
61. Logic-input CMOS quad driver. High peak output current 1.2A. Wide operating range 4.5 to 18V. Device input configuration AND with INV.
62. The effect of rapid thermal processing(RTP) on oxygen precipitates profile and denude zone(DZ) in Czochralski(CZ) silicon wafer during simulating CMOS processing is investigated.
63. Planar spiral inductor is the most important passive component of CMOS RF integrated circuit design.
64. Differential, 8 channel (2 of 16) monolithic CMOS analog multiplexer.
65. With digital processing and reconstruction, an improved selective reset pixel structure and a design of pixel array to extend the dynamic range of CMOS image sensor (CIS) was achieved.
66. Proposed a detection system with Hall effect device array based on FPGA and DSP, the control signal of CMOS analog multiplexer and A/D generated by FPGA was simulated in FPGA d...
67. I have gone back to capacitive coupling from the receiver and also added a zener diode to protect the CMOS parts from possible static issues a little bit better.
68. Using a constant biasing current and a reduced output logic swing, current-steering logic avoids the large digital switching noise of conventional static CMOS logic.
69. The algorithm is employed in a multiple channel CMOS image sampling system and the application test results are excellent.
70. Beginning from the mixed logical expression of the clocked signal, application of theory of transmission-clamping to design low power dissipation CMOS circuits using pulsed power is studied.
71. However, developing C-HMOS called for the creation of ann-well CMOS process, That had not been done previously because CMOS technology grew naturally out of the older p-channel transistor.
72. A digitally controlled CMOS variable gain amplifier base on R 2R ladder resistance network is introduced.
73. Based on the ISFET structure and electronic characteristics, a method integrating the ISFET and signal process circuit realized in an standard CMOS technology are presented.
74. MM5483 is a monolithic integrated circuit utilizing CMOS metal-gate low-threshold enhancement mode devices.
75. A complementary metal oxide semiconductor(CMOS) readout integrated circuit(ROIC) for the sensitive material of vanadium dioxide(VO_2) was introduced.
76. Based on analysis of the principle of substrate current of MOSFETs, a new hot carriers resistant structure of CMOS digital circuits is proposed.
77. This paper describes the design and the principle experiments of a micro digital sun sensor based on a novel diaphragm and active pixel sensor (APS) CMOS image sensor.
78. Low power fast CMOS analog switch. Double pole, single throw (DPST).
79. To boot an operating system, the BIOS runtime searches for devices that are both active and bootable in the order of preference defined by the complementary metal oxide semiconductor (CMOS) settings.
80. Finally, achievements of conversion gain, Linearity and noise figure of CMOS mixers are summarized and compared.
81. This paper puts forward an over current protection circuit for CMOS class - D audio power amplifier applications.
82. V CMOS operational amplifier with rail - to - rail input and output ranges.
83. On the basis of the multiple-valued switch-level algebra, this paper proposes a logic design automation algorithm for NMOS and CMOS combinational circuits.
84. The metal oxides in CMOS and MOSFET devices are not conductors.
85. In this paper, a novel high precision CMOS bandgap voltage reference which uses a negative back circuit and a RC filter to enhance the PSRR is proposed.
86. Because of topology's complexity, there may be several potential parasitic latch-up paths in a CMOS integrated circuit.
87. After comparing the designed circuits with the existing CMOS tristate one, it is showed that they are of the same circuits′ structure.
88. The goal of this work is to use a standard CMOS process to construct a wideband amplifier with low power consumption.
89. It explains the enlarging of CMOS chip and the design of keyboard display interface.
90. CMOS chip 89C52 or 374 on the mother board damaged, can also cause such phenomenon and at the same time, caused much noisy on the small carriage and axis.
12345678