cast iron造句
91) FXD gives greater advantages for aluminum, brass, and cast iron welding, brazing and silver soldering by extremely clean burning.
92) HONIC 400 is not only recommended for cylinder honing on hard, soft and close-grained cast iron but also for flat honing and lapping operations on gauge blocks and gudgeon pins.
93) Cast iron pipe for water supply industry, the market share of around 45 %.
94) Laser cladding bronze alloy process on the surface of nodular cast iron was studied.
95) The conventional viewpoint, which takes flake graphite as voids and cracks, neglects the studying of its fracture behavior and thus limits the deepening under-standing of cast iron nature.
96) Better control of different layer may be essential to good combination of high-speed steel with nodular graphite cast iron.
97) Structure and corrosion behavior of the high silicon cast iron in several different environments have been tested by means of weight-loss analysis and metallograph.
98) An introduction was made to the filtering principles, advantages and shortages of three types of common filters,[http:///cast iron.html] their choice and placement when being used in sand faced cast iron mould process.
99) The effects of nitrogen on the properties of low carbon high chromium cast iron were studied by mechanical property and wear resistance test, and metallograph analysis using OM and ESEM.
100) The paper has made a study with laboratory method on the effect of chemical plating of Ni on the thermal fatigue property of cast iron.
101) The influences of quench and temper treatment on the microstructure and wear resistance of white layer of the chilled cast iron were discussed.
102) The technology for tightness improvement of the Ni austenitic cast iron cable head is studied.
103) NOTE The transmission technique has insufficient sensitiity to detect the discontinuities found in spheroidal graphite cast iron castings and is used in exceptional cases only.
104) The standard materials could be used to the analysis of various alloy cast iron in production.
105) The result showed that this method has an important effect for statistical quality control of chemical composition of cast iron.
106) The artical introduces the simple method and tool for chip breaker of lathe tool lapped by cast iron abrasive wheel in lathe or milling machine.
107) Mold a large cast iron foundry of choice for the production, use and a large number.
108) By comparing and analysing the cane mill roller of creep cast iron made in China and foreign cane mill roller of middle phosphorus.
109) The effect of Si on the crystal lattice parameters, lattice volume and crystal defects of the eutectic cementite in malleable cast iron has been studied by using X ray diffractometer and TEM.
110) The test results shows that there is a linear relationship between Brinell Hardness and the machinability of cast iron with homogeneous microstructure or tiny carbides.
111) Research on HT250 gray iron flame welding with multi-alloying cast iron torch welding rods. Hardness, crack resistance and machinability of the welded joint is tested and analyzed.
112) The other is wear-resistant pipe, including low-alloy steel pipe, alloy cast iron pipes, composite pipe, ceramic pipe, with rubber tubes, polyester materials, pipe, cast stone pipes.
113) Grey cast iron of automobile engine body is treated ( phase - change hardening ) by plasma surface heat treatment.
114) Cast iron , ceramic-cyclone, and the various models Cyclone, different types muffler, boiler drum boiler drum Fan, coal boiler equipment, boiler slag handling equipment for coal layered device.
115) Heat oil in a cast iron pan with 2 inch of oil. Fry each dough to golden brown on both side.
116) NOTE The transmission technique has insufficient sensitivity to detect the discontinuities found in spheroidal graphite cast iron castings and is used in exceptional cases only.
117) The preparation of nano - ceramic composite cutting tools and the advances in the researches on the machinability of cast iron by nano - ceramic composite cutting tools were reviewed.
118) The erosion corrosion behaviors of nodular graphite cast iron samples subject to laser surface melting in a quartz slurry were investigated.
119) An explicit finite—difference method (FDM) was used to model and simulate the solidification of eutectic cast iron by combining heat transfer equations with undercooling nucleation and growth laws.
120) The results also find that wear resistance of niobium cast iron oil ring is 87.3% higher than that of CrMoCu alloy cast iron along with the cost reduction for niobium cast iron oil ring.
123456789